Polyatic Celtic Knot Generator
All tools

Celtic knot generator

Tap between two dots to break the plait. The page counts the cords and keeps every crossing over, under, over.

In a band, a tap is copied along the strip at this spacing. The ends of a band are drawn like a panel's, with no separate corner pieces.

Tap on the line between two dots: left-right of a point places a horizontal break, above-below a vertical one; tap it again to remove it. Tapping the point itself steps through none, horizontal, vertical.

Symmetry

Starting knots

Privacy: the knot stays on this device. It is drawn inside this page and nothing is stored. A share link keeps the grid, the breaks and the style after the # sign, which browsers never send to a server. The page sends an anonymous page-view count and fixed event names only (celtic-make, celtic-download, celtic-download-size-a4 or -letter).

How to use it

  1. Set the width and height in cells (2 to 24 each), or pick a starting knot. With no breaks the grid is a plain plait.
  2. Tap between two dots to place a break; the cords nearby turn back instead of crossing. With Mirror one tap places the break and its left-right twin; with Four-way it also places the top-bottom twins, so the knot stays symmetrical.
  3. Watch the count under the drawing. Colour each cord shows which loops are separate; each swatch can be changed.
  4. Set the knot's width, then save. Print the PDF at 100 % (Actual size, not Fit to page) and measure the 10 cm line; a knot wider than the paper comes out on several pages with dashed overlap lines.

Worked example: why a 4 × 4 plait has four cords

Bain's rule, as Glassner quotes it, is that a plait whose width and height share no factor is a single band, and that a common factor gives several. Counted cord by cord, a plain plait of W × H cells has as many cords as the largest number dividing both W and H: 3 × 4 is one cord, 6 × 4 is two, 4 × 4 is four and 24 × 24 is twenty-four. A 3 × 4 plait has 17 crossings, and its one cord passes each of them twice, 34 crossings in a row, over, under, over. Put one break on any crossing next to the centre of the 4 × 4 plait and the count drops to three: the two cords that met there are joined. On the one-cord 3 × 4 plait, 17 of the 34 possible single breaks do the opposite and split the cord in two (the other 17 keep it whole), so the count can go up as well as down.

What it cannot do

  • Grid knotwork only, with every cord at 45°: no free-hand curves, spirals, key patterns, animals (zoomorphs) or interlaced letters.
  • No automatic “make it one cord”: the count tells you how many there are; you move the breaks.
  • The PDF is lines and fills, not engraving settings or an embroidery-machine file.
  • Colours are a screen and print preview, not matches for any thread, paint or vinyl.
  • A border band has no separate corner pieces; its ends are drawn as a panel's are.
  • The starting knots' names describe what you see; “plait” is the only word taken from the sources, and no knot here is a named traditional design.

Questions

How are Celtic knots drawn on a grid?

With the grid method George Bain published in 1951, refined by his son Iain into what he called the three-grid technique (Andrew Glassner's column, 1999). Lay out a primary grid of dots at the corners of W × H cells and a secondary grid at the cell centres. Draw a plait: cords at 45° that cross at every point midway between two dots, each “going over then under in perfect alternation”. Then add breaklines: a short line between two neighbouring dots of the same grid, horizontal or vertical only. A cord may not cross a breakline, so the crossing there is re-routed into two bends. The panel's edge is broken all the way round, which is why the cords turn back at the sides. Drew's step-by-step page on thinkythings.org does the same by hand: dots at the quarter points of each square, then “break the plait” by erasing chosen crossings.

How do I make a Celtic knot one continuous cord?

Watch the count under the drawing and move breaks until it reads 1 cord. Start from a plain plait whose width and height share no factor (3 × 4, 5 × 6, 7 × 8): it is already one cord. Each break you add either joins two cords into one or splits one into two, so add them a few at a time, symmetrically, and check the count each time. Colour each cord shows exactly which loop is separate, which tells you where a break would join it to its neighbour. The page does not search for a one-cord layout for you.

Can I laser-engrave or cut the knot?

Save the SVG. It is drawn in millimetres at the width you set, and every path in it is a closed outline: each piece of ribbon between two under-crossings is one closed shape, and a cord with no crossings is a pair of closed rings. Each cord is its own group. Laser, vinyl-cutter and plotter software can open an SVG of closed paths; speed, power and cut order are set in that software, not here, and the page has not been tested with any particular machine.

Sources

  • The three-grid technique, breaklines and Bain's one-band rule: Celtic Knotwork, Part 1, Andrew Glassner, IEEE Computer Graphics and Applications, September 1999 (fetched 2026-11-07).
  • Drawing it by hand from dots and breaking the plait: 3-Cord Celtic Knotwork, Drew, thinkythings.org (fetched 2026-11-07).
  • Counting the strands of a grid: Celtic Knotwork Patterns, Joanna Lewis, NRICH, University of Cambridge (fetched 2026-11-07).

Made with AI tools. · Privacy