macrame.SOURCE.txt — where the Macramé mode of /friendship-bracelet-pattern-maker/ gets its numbers and steps (T-PB.370, RULE 1152(a): operator facts are fetched, never remembered). Every page below was fetched on 2026-11-06 with a plain GET; the quotes are copied from the fetched text. fb-macrame.js SOURCES names the same URLs and dates. THE CUT-LENGTH RULE FOR THE WORKING CORDS (two sources; they differ, the page uses the higher figure) 1. GANXXET (a macramé cord supplier), "How to Make a Macrame Bracelet" (blog, published 2022-10-26) https://ganxxet.com/blogs/news/macrame-bracelet (fetched 2026-11-06) "First, you need to measure your wrist to know how big your bracelet needs to be. This is the finished length of your bracelet. But, if you cut your cord to that length now, your bracelet will be too small when you finish the knotting process. After all, those knots reduce its size. To get the length you want, multiply the finished length by five. Then, add five inches to that number. Here's a quick example: Finished length : 7 inches Multiply by five : 35 inches Add five : 40 inches Once you know your final measurement, cut two pieces of cotton cord to that length. Then, cut a filler cord that's 18 inches long." -> used for: WORKING CORD RULE A = 5 x the knotted length + 5 in (12.7 cm), each of the two working cords. Its filler is 18 in for a 7 in bracelet: the length + 11 in. 2. Marching North, "How to Make a 2 Color Macrame Square Knot Bracelet (Reversible!)" https://www.marchingnorth.com/2-color-macrame-square-knot-bracelet-reversible (fetched 2026-11-06; the live page answered 403 to a plain GET, so the text was read from the Wayback Machine copy of the same URL: https://web.archive.org/web/2025/https://www.marchingnorth.com/2-color-macrame-square-knot-bracelet-reversible/) "2 mm Satin Rat Tail Nylon Cord 2 pieces @ 18" long (center cords) 2 pieces @ 34" long (working cords) use 2 different colors for the reversible effect 1 piece @ 14" long (sliding knot closure)" "You'll want to measure the size of the persons wrist that you're making a bracelet for, and tie knots until they're that length. With the 2 mm satin cord, I found that 25 knots was perfect for an adult size bracelet." "It should measure the same length as it did before (about 6" if you're making an adult bracelet with 25 knots)." "Take the left working strand and fold it across the center cords in a "4" shape. Take the right working cord and lay it over the crossed over left cord. Then bring the end under the center cords and through the loop on the left. Pull the ends of the cords to tighten. This is the first half of the square knot. Repeat that process in reverse." "Lay the center cords side by side going in opposite directions. Take the 14" long piece of cord and bring it behind the center cords. Make sure the ends are even. Tie 3 square knots over the overlapped center cords." "Tie an overhand knot in the ends of the center cords." -> used for: WORKING CORD RULE B = 34 in for a 6 in knotted bar = 34/6 (5.67) x the knotted length. THE KNOT HEIGHT: 25 square knots = about 6 in (152.4 mm) on 2 mm cord: 152.4 / 25 = 6.1 mm per square knot (the page's default; a visitor can type their own). THE CORE: 18 in centre cords for a 6 in bar = the bar + 6 in (15.2 cm) at each end. THE SLIDING KNOT: a separate 14 in (35.6 cm) cord, 3 square knots over the overlapped centre cords, an overhand knot in each centre-cord end; the knotted bar is as long as the wrist. THE TWO COLOURS: one working cord in each colour ("for the reversible effect"). Where 1 and 2 differ: rule A (5 x + 12.7 cm) is higher for bars up to 19 cm, rule B (5.67 x) above 19 cm. The page cuts the higher of the two and says which one it used. THE KNOT, STEP BY STEP 3. Yarnspirations, "How To Make 7 Common Macrame Knots and Patterns" https://www.yarnspirations.com/rh-20160411-how-to-make-7-common-macrame-knots-and-patterns.html (fetched 2026-11-06) "The Half Knot is worked with four cords. The two outer cords are the knotting cords and the two center cords are the knot-bearing cords. 1. Bring the left knotting cord to the right over the two knot-bearing cords and underneath the right knotting cord. 2. Bring the right knotting cord to the left under the two knot-bearing cords and over the left knotting cord. 3. Pull knotting cords to secure the knot." "The Square Knot is a continuation of the Half Knot. (The "half" refers to "half of the square".) ... 2. Bring the right knotting cord to the left over the two knot-bearing cords and underneath the left knotting cord. 3. Bring the left knotting cord to the right under the two knot-bearing cords and over the right knotting cord. 4. Pull knotting cords to secure." "A sennit of Half Knots creates a natural spiral" -> used for: the six numbered steps of one square knot, the three of one half knot, and that a half knot is half a square knot (so the page counts a half knot as half a square knot's height). THE SPIRAL'S TWIST (no source measures it exactly; the page draws it "about" every 6 half knots and says so) 4. Build Coded, "Macrame Basics: 7 Essential Knots for Beginners" https://build-coded.pages.dev/macrame-basics-knots-guide/ (fetched 2026-11-06) "Repeat the exact same half knot again. Same hand, same direction. Repeat 6-10 times. After about 4-5 repetitions, the knots start twisting naturally into a spiral. Let them. ... About every 6 half knots, you will want to rotate the work a quarter turn to keep the spiral going in the same direction." -> used for: TWIST_EVERY = 6: the preview draws one offset twist about every 6 half knots, and the steps tell the visitor to let the bar turn. Cord, thickness and tension change the real rate. 5. One Little Project, "How to Make Macrame Bracelets" (print view) https://onelittleproject.com/wprm_print/how-to-make-macrame-bracelets (fetched 2026-11-06) "Repeat the same knot over and over. You will begin to see the bracelet flip on its own and start to create a spiral "helix" pattern. So let the bracelet flip naturally and continue to tie knots the same way." "Fold the 32 inch cord in half and hold the loop at the top. Then wrap the loop around your finger and tie a regular knot, leaving a 1 inch loop above the knot." -> used for: the spiral step wording (let it flip), and the folded core with a loop at the start. THE LOOP AND BUTTON CLOSURE 6. Cut Out + Keep, "Half Knot Spiral Bracelet" (Lys C., 2012) https://www.cutoutandkeep.net/projects/half-knot-spiral-bracelet (fetched 2026-11-06) "Fold both pieces in half and tie a knot just after the fold to form a loop." "To button up the bracelet, take the ends of the strings and pass them trought the button holes. Then make a knot to avoid the button falling down." -> used for: the loop-and-button steps (the core folded to make the loop; the core ends through the button and knotted). 7. "Mixed Knots Macrame Bracelet with Button Closure (Macrame Project #442)", project handout (Word file) https://cdn.shopify.com/s/files/1/0939/2810/files/442_Mixed_Knots_Macrame_Bracelet_with_Button_Closure.docx (fetched 2026-11-06) "Continue tying alternating half hitches until you have a knotted section long enough, when folded in half, for your button to slip through (about 1 1/2" to 2", depending on size of button)." "(1) 1/2" to 3/4" button with shank" -> used for: LOOP_CM = 2.5: a 2 in section folded in half is a loop about 1 in (2.5 cm) long, for a 1/2 to 3/4 in button. 8. USA Jewels, "How to Measure Your Wrist for the Right Bracelet Size" (2026-08-26) https://www.usajewels.com/blog/?p=512 (fetched 2026-11-06) "Snug fit: Add about 1/2 inch (1.3 cm). ... Standard, comfortable fit: Add about 3/4 inch (roughly 2 cm). This is the sweet spot most people land on for everyday wear. Loose, drapey fit: Add about 1 inch (2.5 cm)." -> used for: EASE_CM = 2: a loop-and-button bracelet cannot be tightened, so it closes at the wrist + 2 cm; the loop takes 2.5 cm of that, so the knotted bar is the wrist - 0.5 cm. A sliding-knot bar is the wrist itself (source 2), so the loop-and-button bar is 0.5 cm shorter. A SECOND SLIDING-CLOSURE CORD (checked against source 2's 14 in; the page keeps the higher) 9. Blick Art Materials, "Beaded Macrame Bracelet" (project idea) https://www.dickblick.com/project-ideas/macrame-beaded-bracelet/ (fetched 2026-11-06) "Lay the ends of the bracelet alongside each other as shown. Cut a 12" cord and lay it under your bracelet cords. Using the two bracelet cords as the middle cord, make a short length of square knots" -> used for: the closure cord: 12 in here, 14 in in source 2; the page cuts 35.6 cm (14 in). What none of these sources gives, and the page therefore does not claim: a knot height for other cords (the 6.1 mm is Marching North's 2 mm satin cord; thicker cord makes taller knots, so the page lets the visitor type theirs), and an exact twist rate for the spiral.