Polyatic Weaving Pattern Generator
All tools

Weaving pattern generator

Tap the threading, tie-up and treadling; the cloth is drawn as you go.

Colour to tap onto a thread

Tap the colour row above the threading or the colour column right of the treadling to paint one thread. Names: , or a #rrggbb code.

Top: threading (shaft 1 at the bottom, end 1 at the right). Top right: tie-up. Right: treadling, pick 1 at the top. Under the threading: the drawdown, warp colour = warp on top.

The draft in numbers

Privacy: your draft stays on this device. It is drawn inside this page and nothing is stored; an opened WIF file is read here, never sent. A share link keeps the draft after the # sign, which browsers never send to a server. The page sends an anonymous page-view count and fixed event names only (weave-make, weave-download, weave-download-size-a4 or -letter), never your draft.

How to use it

  1. Pick a starting structure, or Blank, and the number of shafts, treadles, warp ends and weft picks. Making the draft bigger repeats what is already there.
  2. Tap a threading square to put that end on that shaft (tap it again to empty it). Tap tie-up squares to tie or untie a shaft. Tap a treadling square to press that treadle on that pick. The drawdown and the cloth below redraw at once.
  3. Weaving on a table loom? Switch to Lift plan: the page converts the treadling into the shafts raised on each pick and you tap those instead.
  4. Type the warp and weft colour order, for example 4 navy, 2 white, or tap single threads. Check the floats, then save a PDF to take to the loom, a WIF for weaving software, or a share link.

Worked example: 2/2 twill on 4 shafts

Thread the ends 1, 2, 3, 4 and repeat. Tie treadle 1 to shafts 1 and 2, treadle 2 to 2 and 3, treadle 3 to 3 and 4, treadle 4 to 4 and 1, and treadle 1, 2, 3, 4. On pick 1, shafts 1 and 2 rise, so ends 1, 2, 5, 6, 9, 10 … are on top. On pick 2 shafts 2 and 3 rise and the pair moves one end along: ends 2, 3, 6, 7 … Every pick shifts one end, which is the twill diagonal. Every float is 2 long, warp and weft. On a table loom the same cloth is the lift plan 1+2, 2+3, 3+4, 1+4. Switch the shed to Sinking and the same tie-up lowers those shafts instead: the drawdown turns into its negative, the back of the rising-shed cloth.

What it cannot do

  • 8 shafts and 10 treadles at most, and 200 warp ends and 200 picks.
  • No dobby or Jacquard beyond that, and no double-weave layer view.
  • No inkle, tablet weaving or rigid-heddle pick-up.
  • The cloth is an ideal interlacement: no beat, take-up or yarn thickness, so a real weft-faced or loosely sett cloth will look different.
  • No sett, yarn or warp-length calculator.
  • Colours are a preview, not yarn or dye matches.
  • Structure names only where a source gives one; a draft you change is just called a draft.
  • One shaft per warp end: a WIF that threads an end on two shafts is refused. Floats are counted inside the draft as drawn, not across the edge where it repeats.

Questions

How do I read a weaving draft?

A draft has four parts (Gist Yarn's guide). The threading is the grid along the top: each row is a shaft, shaft 1 at the bottom, nearest you, and each column is one warp end, read from right to left; a filled square says which shaft that end goes through. The tie-up is the small square at the top right: its columns are treadles, and a filled square ties that shaft to that treadle. The treadling runs down the right: each row is one pick, read from the top, and the filled square is the treadle you press. The drawdown under the threading is the cloth: a filled square is a place where the warp is lifted over the weft (AdaCAD's rule). To check one pick, follow its treadle up into the tie-up, note the shafts, and every end on those shafts is on top in that row. Swedish drafts put the threading and tie-up at the bottom and mark the shafts that go down, because countermarch looms are tied for both; if a draft woven on a jack loom looks wrong, tie up the empty squares instead (Gist Yarn).

What is a WIF file?

WIF, the Weaving Information File, is the plain-text format weaving programs use to swap drafts; the WIF 1.1 specification dates from April 20, 1997. It is laid out like a Windows .ini file. [WEAVING] gives the shafts, the treadles and whether the shed rises; [THREADING] lists end=shaft, [TIEUP] treadle=shafts, [TREADLING] pick=treadle and [LIFTPLAN] pick=shafts raised; [COLOR TABLE], [WARP COLORS] and [WEFT COLORS] carry the colours. Missing lines mean an empty thread. This page writes WIF 1.1 and opens WIF files from other programs. It refuses, and says why, a file over 512 KB, more than 8 shafts, 10 treadles or 200 threads, an end on two shafts, or a line pointing at a shaft or treadle the file does not declare.

Can I use it for a table loom?

Yes. Switch the right-hand block from Treadling to Lift plan. A table loom, or any direct-tie loom worked with levers, has no treadles, so each pick is written as the shafts you raise. The page converts for you: each pick's lift is the shafts tied to its treadle on a rising shed, or every shaft that is not tied on a sinking shed, and the drawdown stays the same (AdaCAD describes the same conversion). The PDF and the WIF then carry the lift plan as numbers, such as pick 1: 1+2, pick 2: 2+3. Switching back to Treadling makes one treadle for each different lift, up to 10.

Sources

Made with AI tools. · Privacy