Polyatic Felt Christmas tree pattern
Tools

Felt Christmas tree pattern

Type the height. Print the sheets, tape them, cut the felt.

Your felt tree

120 cm · Classic tiers

See the sheets to print
Sheet 1

Your tree

120 cm
Look
optional

The name is cut in the round letters of the felt ornament patterns and added at the end of the PDF. It stays on this device.

Paper
Felt to buy

    Area of the pieces plus 30 % for the offcuts between slanted edges on craft sheets; on the roll, the pieces packed side by side 1 cm apart. Single ornaments for the tree are on felt Christmas ornament patterns.

    3D felt Christmas tree: two pieces that slot together

    A tabletop tree that stands on its own. The slots are cut as wide as your felt is thick, so the pieces grip without glue.

    Toddler stick-on set: felt sticks to felt

    Big one-piece shapes little hands can press onto the tree and pull off again. No sewing, no glue, nothing small.

    How to make a felt Christmas tree for the wall

    1. Pick the height of the finished tree, from the tip of the star to the foot of the trunk. 90 cm suits a door, 120 to 150 cm a free wall, 180 cm a tree a child stands next to. The pattern is drawn at exactly that height; the first sheet shows the finished tree with its measurement.
    2. Print at actual size (100 %), never "Fit to page", and check the 5 cm ruler at the foot of a sheet. A 120 cm tree takes about 18 A4 sheets, a 180 cm tree about 35, because the pieces are big.
    3. Tape the sheets in the grid of the layout map on sheet 1 (A1, A2, B1 …). Trim the left and top margin of a sheet on the dotted line, lay it over its neighbour so the little crosses sit on top of each other, and tape. Sheets the map marks with a dash hold nothing and are not printed.
    4. Cut the paper pieces on the solid line, pin or tape them to the felt and cut the felt with sharp fabric scissors. The dashed line across a tier shows where the tier above overlaps it.
    5. Hang it from the bottom up: trunk, bottom tier, the tiers above, the star last. Removable mounting strips or poster putty at the top of each tier hold felt on paint and on a door; a few pins hold it on a cork board or fabric wall.

    Questions

    Is the felt Christmas tree pattern free and printable?

    Yes. The pattern is drawn in your browser and saved as a PDF or PNG you print at home: no account, no watermark, no upload. Use it at home, in a classroom or for a nursery wall.

    Can I get the pattern as a PDF?

    Yes: Download PDF gives every sheet in one file, the layout map first, then the pattern sheets in the order of the map. A4 or US Letter; US and Canadian browsers start on Letter. If you add a name, the letters come on the last sheets. PNG saves the sheet you are looking at, at 300 dpi.

    How much felt do I need for a felt Christmas tree?

    The list under the form gives it for your height and look, colour by colour. Two worked numbers for the classic look: a 120 cm tree needs about 0.36 m² of green, which is 4 craft sheets of 30 × 45 cm or about 1.15 m of a 90 cm wide roll; a 180 cm tree needs 0.80 m², 8 sheets or about 2.1 m of roll. The bottom tier of a tree over about 80 cm is wider than one craft sheet, so for big trees a roll is easier; with sheets, butt two together behind the tier and glue a strip of felt over the join.

    How do I make a 3D felt Christmas tree?

    Use the 3D tree above: two identical tree shapes, one with a slot from the bottom up to half height, one with a slot from the top down to half height. Slide one onto the other and the tree stands as a cross. Pick the thickness of your felt (1, 1.5, 2 or 3 mm) because the slot is cut exactly that wide; a 1 mm felt is floppy at 22 cm, so use stiffened felt or 2 to 3 mm wool felt for the bigger sizes.

    Is a felt tree safe for a toddler?

    The toddler set is made for it: twelve one-piece shapes (bauble, star, present, candy cane, gingerbread man, bell, snowman, stocking, Santa, reindeer, angel, poinsettia), each at least 32 mm across in every direction, which is wider than the 31.7 mm small-parts test tube toy makers use, and nothing sewn or glued on that could come off. Felt can still be chewed and torn, so stay close while a little one plays. Wool-blend or fuzzy felt clings to a felt tree; slick acrylic felt slides off it.

    Where are the ornaments?

    The stick-on set above is the simple, toddler-proof version. For sewn ornaments with several colours (Santa with his hat and beard, a nativity, a photo bauble) use felt Christmas ornament patterns, at 8 to 12 cm for a tree of 120 cm or more.

    Made with AI tools. · Privacy